必须具有路由器夹具:榫眼门硬件与此自定义指南
我是加里斯特格勒。我想和你分享一些让你的生活更简单的东西,任何时候你都有门硬件。这可能是你需要夹具的最常见的门硬件,因为你当然不想用凿子拿出来。这是我们制作溃败的简单模板和关于这个我最爱的一部分,但它是如此的关键,这个jig是我想挖出的概要的大小。我将使用的路由器位是这个。现在这是一个1/2英寸的外径路由器位,1/2英寸轴承上方。现在你想要谨慎地买这样的谨慎这一点,因为有时候这个轴承比这更大,这只是使它真的很复杂,你必须考虑比你的模板在更大的模板中删除你需要。所以总是给你一个1/2英寸的直径位,上面的1/2英寸轴承,然后一切都会很棒。这个罢工板确实有1/4英寸半径,其中一些是方形的。 If you’re going to want those just use a chisel to square the corners out. Now one other thing, you can also get- bits like this are actually a lot easier to come by at most stores and if all you can do is find one like this that’s deeper, don’t worry, you can still make the template. Basically, you just have to put 2 of these together, it’s an inch and 1/2 and then you have something for the bearing to ride on and it’ll still cut. The best thing to do if you can do it is to get the shorter one. Alright, we talked a whole bunch about bits and things, now how does this work? Again, it’s really really simple. All I have to do is lay the jig onto of the door jamb where I want to rout the strike, and I’m going to flush the edge up with the edge of the door jamb and then I’ll use this headless pinner, just a couple headless pins, to hold my template in place. Headless pins are so small you’ll hardly even notice that they’re there and what I’ll actually do is wiggle that headless pin back and forth and break it off so it’ll break off below the surface of the template. Don’t cut it off or else you’ll get something that’ll really cut your finger up. If this was stain grade you might not want to use the headless pin. personally, I think the pin is so small it doesn’t make any difference. But if you want to clamp it and make your life more difficult, go ahead.
这只是简单。我现在要做的就是撬开这个,我有完美的溃败。如果我钻了钻孔,它会在那里掉下来。因此,您可以使用这种非常相同的原则,就像造成门的铰链,或者稍微不同于做闩锁板。但原理只是在一块木头中剪掉,这正是你想要溃败的尺寸。我甚至制作了模板,我们在那里我们在那里同时做了3或4个铰链,以及它的伟大事件是它需要误差的误差,你可能不得不从铰链铰接到铰链。所以,你可以在一块胶合板中制作3个缺口,一次做整门。这是一个伟大但简单的夹具。
更多的必备路由器夹具:
- 使用此自定义指南的榫眼门硬件
- 使用商店建造的模板制作任何插入楣板或面板模式
- 使用此灵活模板进行复杂的S曲线
- 磨机装饰着自制指南针
- 用这个简单的指南切割干净,直的爸爸
阅读加里文章工作网站路由器夹具从问题#280